feed inlet
英 [fiːd ˈɪnlet]
美 [fiːd ˈɪnlet]
进料口；加料口
双语例句
- The feed inlet and outlet adopt block type structure to provide easy operation.
进、出料口采用撞块式结构方便操作。 - The feed inlet of the tank body is provided with a feed inlet valve, and materials falling buffer mechanisms are arranged in the tank body in different heights.
罐体进料口设有进料阀，罐体内不同高度设有物料下落缓冲机构。 - Fit oil feed housing of inlet camshaft.
安装进气凸轮轴的机油供给室。 - A step seal with a rubber gasket is used in a feed inlet, a feed outlet and an input and output end covers of the utility model.
该磨机进、出料口和进、出端盖之间采用带橡胶垫圈的台阶密封。 - The crude methanol pre-fractionator is calculated by the application of improved opposite triangle matrix technique and UNIFAC model, and crude methanol water addition, number of trays, reflux ratio and feed inlet location etc are analyzed.
应用改进的三对角矩阵法和UNIFAC模型，对粗甲醇预蒸馏塔进行了模拟计算，并对粗甲醇加水量、塔板数、回流比和进料位置等进行了分析和讨论。 - At all times, the slurry leakage in the feed inlet of the autogenous tumbling mill chiefly influences the operation efficiency of the mill, which affects the production, quickens the abrasion of the quill shaft, increases the maintenance time and decreases the lifespan of the mill.
自磨机进料端漏浆问题一直是影响自磨机运转率的主要原因，它影响生产，加剧中空轴的磨损，增加维修时间又降低设备的使用寿命。 - Study to the Slurry Leakage in the Feed Inlet of the Autogenous Tumbling Mill
自磨机进料端漏浆问题研究 - Experimental set-up is consists of a side inlet duct and a side circulating feed inlet, and venturi-pipe that was extensively used in industry as gas distributor.
实验装置采用侧向进气结构和回料装置，气体分布器采用工业上推广使用的文丘里管。 - In this paper the research work has been put on the Model 490Q engine by changing the diesel/ LPG dual-fuel technique through using ECU to control the air feed mode of the inlet channel blender.
实验采用单片机控制进气道预混合混合器的供气方式，对490Q直喷式柴油机进行了柴油／LPG双燃料的技术改造。 - Based on the designed thin film evaporator, the influence of the rotor speed, feed rate and liquid inlet temperature on evaporation length and film heat transfer coefficient was primarily discussed using the software CFX 4.4 with water as feed liquid.
针对自行设计的薄膜蒸发器，以水为物料，采用大型CFD软件CFX4.4，初步探讨了刮板转速、进料量、进料温度等参量对薄膜蒸发器蒸发段长度和加热段膜内传热系数的影响。 - Several technical measures, such as applying high efficency packing instead of trays to improve the separation in vacuum distillation, and using new type of feed inlet structure to decrease the entrainment and the residuum carry, etc.
采用新型的塔进料结构，减少雾沫夹带及渣油携带，并对减压塔进行了技术改造的计算机模拟研究。 - The cavitation model can calculate the real-time actual flow and the cavitation critical flow of the feed water pump using the process parameters ( rotational speed, inlet pressure, outlet pressure etc).
使用给水泵运行的过程参数（泵的转速、进口压力、出口压力等），该汽蚀模型可以实时计算泵的工作流量和汽蚀临界流量。 - Emulsion in the feed temperature is 30 ℃, inlet temperature of 200 ℃, the air temperature of 90 ℃ under the conditions obtained by spray drying microencapsulation of Spirulina products.
乳化液在进料温度为30℃，进风温度200℃，出风温度90℃的条件下喷雾干燥制得螺旋藻微胶囊化产品。